Decorative Plaster Mouldings: Manufacture And Installation

In rooms with high ceilings can often find a moulding as a Decorative Plaster Mouldings. Such a product is different from the foamed even by visual inspection, as a plinth, and the foam is much broader in its structure and strength there is monumental.

Decorative Plaster Mouldings preserved, probably, almost all official buildings formerly belonging to noble families, which indicates that the origins of the decoration.

How To Make Decorative Plaster Mouldings And Install It In The Room?

In order to make gypsum mouldings need silicone mold for casting and plaster box, which does not allow to deform the shape if it accidentally cadent.

To fill better use major sates solution or as much as is necessary, therefore, fill the form with water and pour the water into the tank for a solution. So you determine how much gypsum is necessary to prepare for a casting.

Plaster cornice

First, you pour in a bucket of water, and then begin to pour plaster, stirring it, should get the consistency of a rare type of sour cream. Gives a ready solution for 10 minutes and pour it into a mold for casting.

When you fill in the form below eaves, do not fill it to the brim, so that you have the ability to remove air bubbles from the solution. The air is removed by shaking all the edges and in turn how these bubbles come out, it will be visible on the surface.

Gypsum, which spilled on the edges of the form, collects a spatula and drops it back into shape.

Cornice, exactly the same as the ceiling tiles need to be reinforced for strength gypsum ceiling design. To do this, use hemp, hemp, kindling, aluminum or copper wire. Reinforcement is placed on the surface and smooth with a spatula, and then poured the rest of the solution from the tank, but it has to be stirred before it.

Align gypsum wide spatula and give the product a little dry (surface upon setting becomes matte color), and then pass the spatula again, as if grasping Gypsum will be heated and the bubble. Then make an incision.

Watch this video

 

After 15-20 minutes, you can remove the cornice of the form. To do this, gently turn the box upside down and remove it from the form and the form itself begins to appear from the middle to the edges of the plinth.

Form insert back into the box, and the cornice put on a flat surface to complete solidification.

Installation of the Decorative Plaster Mouldings

Mounted plaster cornices on water adhesives or putty. If the ledge is too heavy, it can be fixed with screws to the wall. Installing the plinth starts with the room.

Cornice is put in the starting position, pushing his butt to conjugate the wall, as seen in the picture, and on it, on the wall and ceiling held the line. The same is done with the other hand.

Now, when you apply a plinth, his cross lines that mark the neighboring cornice. At the intersections are putting labels on the ledge, and circumcised him 45⁰ at an angle to the base. The same is done with different eaves.

Cutting gypsum ceiling products for use finely toothed handsaw or hacksaw, then obtain a clean cut and neat.

Install two conjugate cornice to you to make sure the correct trim angle . To dock the baseboards in the span wall trimming is done on 90⁰, moreover, both better crop plinth, then the cut will be more accurate, and the gap when connecting – to a minimum.

Seams and gaps sealed with putty, which is applied by squeezing a syringe. Extruded strip of putty to gently smudge with your finger to not only seal the gap formed, but did not damage the decorative relief, smeared with a layer of putty.

After drying and painting eaves they can apply gold leaf. Bronze, of course, not the only paint for stucco, but it is used most often.

Set gypsum cornice is not very difficult, but this type of stucco is not appropriate in any room, such as a cornice will not look at the ceiling in a low Khrushchev. Great scope for moldings opens in stalinkas where ceilings reach three meters and above.

Get free price quotes for Fibrous Plaster Coving, plaster cornice, corbels and mouldings UK

Visit Website: www.Cornicedesigns.co.uk
Phone: 01709 431446
Unit 3 Bolton Road Business Centre,
Bolton Road, S63 7JY Rotherham
enquiries@cornicedesigns.co.uk